欧美成人精品A片免费一区99,三上悠亚在线观看,国产裸体舞一区二区三区,SPY3WC撒SPY3WC撒尿

北京北廣精儀儀器設備有限公司
免費會員

當前位置:北京北廣精儀儀器設備有限公司>>電壓擊穿試驗儀>> BDJC-150kv絕緣材料擊穿強度測試儀/硫化橡膠電氣強度測試儀 擊穿電壓測定儀

絕緣材料擊穿強度測試儀/硫化橡膠電氣強度測試儀 擊穿電壓測定儀

參  考  價面議
具體成交價以合同協議為準

產品型號BDJC-150kv

品       牌

廠商性質生產商

所  在  地北京市

更新時間:2024-08-03 17:01:16瀏覽次數:66次

聯系我時,請告知來自 塑料機械網
絕緣材料擊穿強度測試儀/硫化橡膠電氣強度測試儀電壓擊穿試驗儀,介電擊穿強度試驗儀,耐電壓擊穿測試儀,工頻電壓擊穿測試儀,電壓擊穿儀,工頻介電擊穿強度測定儀,工頻耐電壓擊穿試驗機,電壓擊穿試驗機,絕緣材料電氣強度測試儀,擊穿強度試驗儀,電氣強度測試儀,介電強度試驗機,擊穿電壓試驗機,電氣介電強度試驗儀,固體絕緣材料電氣強度試驗儀,硫化橡膠工頻擊穿電壓強度耐電壓擊穿測定儀,

一、絕緣材料擊穿強度測試儀/硫化橡膠電氣強度測試儀滿足標準:

1、GB1408.1-2006《絕緣材料電氣強度試驗方法》
2、GB1408.2-2006《絕緣材料電氣強度試驗方法 
        第2部分:對應用直流電壓試驗的附加要求》
3、GB/T1695-2005《硫化橡膠工頻擊穿電壓強度和耐電壓的測定方法》
4、GB/T3333 電纜紙工頻電壓擊穿試驗方法
5、HG/T 3330絕緣漆漆膜擊穿強度測定法
6、GB12656 電容器紙工頻電壓擊穿試驗方法
7、ASTM D149《固體電絕緣材料工業電源頻率下的介介電強度的試驗方法》


二、絕緣材料擊穿強度測試儀/硫化橡膠電氣強度測試儀主要用途:

BDJC-150KV電壓擊穿試驗儀主要適用于固體絕緣材料如:塑料、薄膜、樹脂、云母、陶瓷、玻璃、絕緣漆等介質在工頻電壓或直流電壓下擊穿強度和耐電壓時間的測試。

⒈擊穿電壓(V):用連續均勻升壓的辦法對試樣施加工頻電壓并保持試樣發生擊穿時的電壓值,以kV表示。

⒉擊穿強度(E):試樣的擊穿電壓值與兩個電極間試樣的平均厚度之商,以kV/mm。

三、詳細參數:

序號

項目

參數

1

輸入電壓

AC220V   50Hz

2

輸出電壓

AC 0-50KV DC 0-50KV

3

輸出功率

5KVA

4

測量范圍

0-50KV

5

測量誤差

≤2%

6

升壓速率

0.1KV/S-3KV/S

7

耐壓時間

0-4H

8

長×寬×高

700mm×800mm×1650mm

 

四、配置:

序號

配置

數量/單位

1

主機

一臺

2

油盒

一個

3

電極

三個

5

放電裝置

一套

6

試驗軟件

一套

7

計算機+打印機

一套

8

檢測證書

一份

 

五、產品特點:

1、運行于WIN  XP/WIN7/WIN8系統下的獨立安裝軟件,界面友好,操作簡單

2、實驗顯示曲線,數據自動儲存,自動查找

3、多種用途可以進行交、直流試驗試驗準確、可靠、安全

4、計算機控制試驗過程,自動判斷停止,自動復位

5、超壓、過流、短路、漏電、誤操作等多種保護

 

六、注意事項:

1、試驗過程中不能讓無關人員靠近,因本試驗儀器可產生較高的電壓,未經過培訓的人員不能使用該設備。試驗時要有監護人員,不要單人使用。以防萬一發生意外情況。

2、長時間不使用設備,在再使用時,先讓儀器空載加壓一次,即把高壓電極的接線從均壓球上取下。查看計算機試驗界面,看看高壓電壓是否正常。

3、試驗中發生意外情況要及時切斷電源,問題處理后才能繼續試驗。

4、設備安放要平穩,安放的地面要堅固。是水泥地面以免產生共振。

5、該設備在使用中外殼要接保護地線,既設備外殼接大地,以保護操作人員和設備運行的安全。

6、使用完設備后,要關掉系統各部分電源,不準帶電插拔電源線。

7、要按規定的電源電壓接入設備。確保電路接線正確。否則會損壞設備。

8、該儀器需安置在室內,實驗室應整潔、干燥、無腐蝕性介質,非相關人員不要隨意操作。

9、不要讓設備電纜碰到尖邊,以免劃破電纜絕緣;不要讓電纜壓在重物之下,以免壓斷電纜引起火災;不要用電纜拉物體或用電纜捆綁物體,以免拉斷電纜使設備不能正常運轉。

10、不要讓設備碰到水濺,腐蝕性氣體,可燃氣體和可燃物。如果不避免,可能火災。

11、搬動設備時,要切斷設備電源,既要把插頭從插座中拔下。禁止搬動設備時放倒設備或傾斜45°角以上。

12、不要在設備運行時插拔設備的電源插頭。

 

電壓擊穿試驗儀

 Meet the standard:
1, GB1408.1-2006 "electrical strength of insulating materials test method"
2, GB1408.2-2006 "test method of electrical strength of insulating materials
The second part: the application of DC voltage test to the additional requirements
3, GB/T1695-2005 "vulcanized rubber power frequency breakdown voltage strength and resistance to voltage measurement method"
4, GB/T3333 cable paper power frequency voltage breakdown test method
5, HG/T 3330 insulation paint film breakdown strength test method
6, GB12656 capacitor paper power frequency voltage breakdown test method
7. D149 ASTM test method for dielectric strength of solid electrical insulating materials at industrial power frequency
Main use:
Mainly applicable to solid insulation materials such as: plastic, film, resin, mica, ceramic, glass, insulating paint and other media in the
Power frequency voltage or DC voltage breakdown strength and voltage endurance test.
The breakdown voltage (V): with a continuous and uniform boost way of sample applied voltage and keep the sample breakdown voltage value, in kV said.
The breakdown strength (E): the breakdown voltage of the sample thickness and the average value between the two electrodes of the sample, to kV/mm.
parameter
Input voltage AC 220 V
Output voltage AC KV 0--100 DC 0 - 100 KV
Electrical capacity 5KVA
High pressure classification 0-10KV, 0--50KV, 0-100KV
Boost rate 200V/S 100V/S 500 V/S 1000 2000V/S 5000V/S V/S, etc.
Test methods: DC test: 1, uniform step up 2, gradient boost 3, pressure test
AC test: 1, uniform step up 2, gradient boost 3, pressure test
Test medium air, test oil
The precision is less than or equal to 1% voltage test.
Test voltage continuously adjustable KV 0--100
Product features:
1, running in the XP/WIN7/WIN8 WIN system under the independent installation software, friendly interface, easy to operate
2, the experiment shows the curve, the data automatic storage, automatic search
3, a variety of uses can be carried out, DC test test is accurate, reliable and safe
4, computer control test process, automatic judgment stop, automatic reset
5, over voltage, over current, short circuit, leakage, wrong operation and other protection
Matters needing attention:
1, the test process can not let the irrelevant personnel close, because the test instrument can produce a higher voltage, not through the training of personnel can not use the device. When testing, there should be a guardian, not a single use. In case of accident.
2, for a long time without the use of equipment, in the re-use, the first time to let the instrument pressure once, that is, the high-voltage electrode wiring from the uniform pressure on the ball to take off. View the computer test interface, to see if the normal voltage is normal.
3, the accident occurred in a timely manner to cut off the power supply, the problem can continue to test after treatment.
4, the equipment should be placed on the ground to be stable. It is better to cement the ground so as to avoid resonance.
5, the equipment in the use of the shell to be connected to the protection of the ground, both equipment enclosure to the earth, in order to protect the operation of personnel and equipment safety.
6, after the use of the device, to turn off the power supply of the system, are not allowed to plug the power line.
7, according to the provisions of the power supply voltage access equipment. Make sure the circuit connection is correct. Otherwise it will damage the device.
8, the instrument should be placed in the room, the laboratory should be clean, dry, non corrosive media, non related personnel do not operate at random.
9, don't let cable equipment encountered sharp edges, so as not to cut the cable insulation; don't let cable in under heavy pressure, to avoid pressure broken cable caused by fire; don't cable pull objects or objects tied with a cable, so as not to pull off the cable so that the device is not functioning properly.
10, do not let the equipment encountered water splashing, corrosive gases, flammable gases and fuel. If you don't avoid it, it may be a fire.
11, devices, to cut off the power supply equipment, is to unplug the plug from the socket. No equipment or equipment moving down tilt angle of 45 degrees or above.
12. Do not plug the power plug of the device when the device is running.

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

X
該信息已收藏!
標簽:
保存成功

(空格分隔,最多3個,單個標簽最多10個字符)

常用:

提示

X
您的留言已提交成功!我們將在第一時間回復您~
在線留言