注塑機 擠出機 造粒機 吹膜機 吹塑機 吹瓶機 成型機 吸塑機 滾塑機 管材生產線 板材生產線 型材生產線 片材生產線 發泡設備 塑料壓延機
四川川大干燥科技工程有限責任公司
四川川大干燥科技工程有限責任公司
暫無信息 |
一、工作原理及應用范圍介紹IntroductionofWorkingPrincipleandScopeofApplication將需要造粒的主料和輔料按合適的比例和配方加入到該設備的攪拌容器內，粉體物料和粘結劑在圓筒形容器中由底部混合槳經過高速充分混合后，形成濕潤軟材，然后由側置的高速粉碎槳切割成均勻的濕顆粒，從而實現了造粒的目的
一、工作原理及應用范圍介紹
Introduction of Working Principle and Scope of Application
將需要造粒的主料和輔料按合適的比例和配方加入到該設備的攪拌容器內，粉體物料和粘結劑在圓筒形容器中由底部混合槳經過高速充分混合后，形成濕潤軟材，然后由側置的高速粉碎槳切割成均勻的濕顆粒，從而實現了造粒的目的。該設備也可以選配真空干燥和輔助系統設備來實現一步到位，直接獲得成品。
該設備尤其適用于輕質細粉物料的造粒。細粉物料微粒越細，經造粒后顆粒的球形度越高，成球質量越好，一般要求物料造粒前的粒度應小于200目為宜。主要應用的領域有：制藥產品、食品和飼料、陶瓷產品、塑料、橡膠、輪胎、聚合物和樹脂、生化產品、化學品及化肥、香水、色素和染料、蔬菜和植物提取物、芳香物、糧食產品等。The major and auxiliary materials for pelleting are added in the stirred vessel of this equipment as per proper proportion and formula; the powder materials and binder are fully mixed at the bottom of cylindrical vessel by mixing blade at high speed to form the wet non-rigidmaterial, and then cut into even wet granule by high-speed crushing blade set on the side, thus to realize the pelleting purpose. This equipment may be provided with vacuum drying and auxiliary system to produce the finished product in one step.
The equipment is particularly applicable to the pelleting of light fine materials. The finer fine materials may result in high sphericility and good pelletization quality after the pelleting. In general, the particle size of material is proper to be less than 200 meshes. This equipment is mainly applied in the pharmaceutical product, food and feed, ceramic product, plastic, rubber, tire, polymer and resin, biochemical product, chemicals and fertilizer, perfume, pigment and dye, vegetables and plant extracts, aromatic substance, and food products.
二、特點
Characteristics
1.動態化造粒，成粒近似球形，流動性好。
2.每次干混2分鐘，造粒1-4分鐘，效率高。
3.在同一封閉容器內完成混合、潤濕、制粒，粉塵外泄少，一次實現干混-濕混-制粒,工藝縮減,符合GMP規范。
4.操作簡單，易于清洗，混合速度可調（據需要）。
5.采用PLC可編程控制，可實現智能化、信息化操作。
1. The dynamic pelleting produces near-sphericalgranule and good mobility.
2. Only 2min and 1-4min are required for each dry mixing and pelleting respectively, resulting in high efficiency.
3. The mixing, wetting and pelleting are completed in one sealed container with little dust discharged, realizing the dry mixing-wet mixing-pelleting in one step with reduced process steps, and complying with GMP codes.
4. It is also featured by simple operation, easy to clean and adjustable mixing speed (as required).
5. The PLCprogrammable control is adopted to realize the intelligent and information operation.
三、技術參數（下表中數值僅供選型時參考）濕法制粒機
Technical parameters (the values in the table below are for reference in type selection only)
四、結構簡圖Dimension sketch
濕法造粒機
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
塑料機械網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
