電纜絕緣PE原料,Favorite REG100
Favorite REG100 PE理化性能
物料性能 耐腐蝕性,電絕緣性(尤其高頻絕緣性)優良,可以氯化,輻照改性,可用玻璃纖維增強.低壓聚乙烯的熔點,剛性,硬度和強度較高,吸水性小,有良好的電性能和耐輻射性;高壓聚乙烯的柔軟性,伸長率,沖擊強度和滲透性較好;超高分子量聚乙烯沖擊強度高,耐疲勞,耐磨. 低壓聚乙烯適于制作耐腐蝕零件和絕緣零件;高壓聚乙烯適于制作薄膜等;超高分子量聚乙烯適于制作減震,耐磨及傳動零件. 成型性能 1.結晶料,吸濕小,不須充分干燥,流動性*流動性對壓力敏感,成型時宜用高壓注射,料溫均勻,填充速度快,保壓充分.不宜用直接澆口,以防收縮不均,內應力增大.注意選擇澆口位置,防止產生縮孔和變形. 2.收縮范圍和收縮值大,方向性明顯,易變形翹曲.冷卻速度宜慢,模具設冷料穴,并有冷卻系統. 3.加熱時間不宜過長,否則會發生分解,灼傷. 4.軟質塑件有較淺的側凹槽時,可強行脫模. 5.可能發生融體破裂,不宜與有機溶劑接觸,以防開裂. 專業代理以下產品,免費提供COA,SGS,UL黃卡,加工參數 。索取 直線:86-傳真:86-李生:
Favorite A170 | Favorite Plastics | PE,未 |
Favorite A180 | Favorite Plastics | PE,未 |
Favorite A190 | Favorite Plastics | PE,未 |
Favorite A401 | Favorite Plastics | PE,未 |
Favorite BI523 | Favorite Plastics | PE 合金 |
Favorite EVA300 | Favorite Plastics | EVA |
Favorite EVA600 | Favorite Plastics | EVA |
Favorite INSTATEAR | Favorite Plastics | PE 合金 |
Favorite LL051 | Favorite Plastics | LDPE LLDPE |
Favorite LL303 | Favorite Plastics | LDPE LLDPE |
Favorite LL505 | Favorite Plastics | LDPE LLDPE |
Favorite LL506 | Favorite Plastics | LLDPE EVA |
Favorite LL508H | Favorite Plastics | LLDPE EVA |
Favorite LL515 | Favorite Plastics | LDPE LLDPE |
Favorite LL565 | Favorite Plastics | LLDPE EVA |
Favorite LL660 | Favorite Plastics | LLDPE MMW-HDPE |
Favorite MDLLN | Favorite Plastics | PE,未 |
Favorite REG100 | Favorite Plastics | PE,未 |
Favorite REG101 | Favorite Plastics | PE,未 |
Favorite REG200 | Favorite Plastics | PE,未 |
Favorite REG235 | Favorite Plastics | PE,未 |
Favorite REG250 | Favorite Plastics | PE,未 |
Favorite UL735 | Favorite Plastics | ULDPE EVA |