泉州聯進機械有限公司
QUANZHOU LIANJIN MACHINE CO., LTD
切
條
機
使
用
說
明
Rubber Strip Cutting Machine Usage
用途：用于橡膠切條、切紙等
特點： 1.裝有防護裝置在使用時安全快捷。
2.翻滾切割，三個刀片設計，切料速度快，效率高。
3.送料速度可調，裁斷寬度可調。
主要技術參數 Technical Parameters | |
型號 Model | LJ-CA08 |
機型Systems | 翻滾切 |
外型尺寸Appearance Size: L*W*H(mm) | 1200*1000*1200 |
工作寬度Working Width(mm) | 600 |
功率Power (KW) | 2.25 |
重量Weight(kg) | 350 |
使用說明
1. 操作時不要雙層料同時切，以免燒壞電機，發現送料滾筒卷料時，要及時關機清理，同時如有雜料在刀口工作部位要及時清理干凈，清理時務必斷開電源來源。
2. 原料不能有鐵，石頭等雜物，如發現要清理干凈，以免損傷刀片。
3. 發現電機有異聲，要停機檢查，鏈條皮帶松動要及時調整，螺絲松動要及時緊固。
4. 機臺工作時，手一定不要伸進里面，如有問題，一定要停機解決。
5. 手搖加油泵一個星期加油一次，每次壓兩下；腳踏板要輕踩輕放，以免兩頭軸心變位。
6. 如時間長，發現料切不斷①調整刀口間隙②修整刀口，檢查刀口是否有損壞，如有損壞要及時修整。
7. 送料滾筒如，不能啟動①檢查電控箱內保險絲是否燒壞，如燒壞，更換時必需按原來型號更換，不要隨意加大規格。②檢查調整旋轉失靈，如有不靈及時更換。
8. 兩端彈簧調整不能壓得太緊，以免滾卷料，新機臺用少量粉撒在卷筒上，以免卷料。
Size: L*W*H (mm) 1200*1000*1200
Purpose: This machine is used for cutting the rubber, paper etc.
Advantage: 1.Equiped with safety cover to secure safety on working.
2. Revolving blade cuts rubber in high speed and efficiency, with three blade edges.
3. Adjusting with the width of rubber strip through the speed button on the side.
主要技術參數 Technical Parameters | |
型號 Model | LJ-CA08 |
機型Systems | 翻滾切 |
外型尺寸Appearance Size: L*W*H(mm) | 1200*1000*1200 |
工作寬度Working Width(mm) | 600 |
功率Power (KW) | 2.25 |
重量Weight(kg) | 350 |
INSTRUCTIONS:
1. When operating, do not cut rubber in double-deck at one time, which will cause the MOTOR to be too hot and broken. If the Material-sending Roller can not run smoothly. Please shutdown at once; meanwhile, if there are odds and ends at knife edge, please clean up in time .Do stop the power before cleaning.
2. No iron or stone in the material; if any, take them, away at once, so as not to make the blade damaged.
3. Any unusual voice, stop and check. Adjust chains and screws if they are loose.
4. Do stop the machine when there is problem. Do not put hands in when the machine is still working.
5. Add oil to cycloidal needle wheel on time (usually once per three months).
6. After being operated for long time and the machine fails to cut off material, customer should adjust the knife and check whether the blade is damaged and need repairing.
7. In case the material sending roller can not send the material smoothly, you should firstly check and adjust rotary switch; if it can not work effectively, replace a new one in time.
8. Do not install the spring at each side too heavily or the material will not be sent smoothly. New machine please add proper amount of powder to the Rooller to avoid material rolling and jammed.
